Hong Kong RC Sailplane Forum 香港滑翔機發燒友論壇

This forum is dedicated to r/c sailplane enthusiasts 此論壇專為遙控滑翔機發燒友而設
It is currently 23 Oct 2017 06:51 am

All times are UTC + 8 hours




Post new topic Reply to topic  [ 10 posts ] 
Author Message
 Post subject: Wing repairing
PostPosted: 14 Sep 2005 08:45 pm 
User avatar

Joined: 03 Mar 2004 07:31 pm
Posts: 1020
Let me kick off this page.
:P :P
This wing (shooting star) was given to me by a master years ago. Please note that the centre section of the wing is intact. Placing it into the trash is a shame. I decided to keep it, as it worth for attention.

Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Use only micro balloon, but not other filler, as they are heavy. Furthermore, if you wish the surface smooth, use a 'SK-II' stirler!!

Will post the progress next time, regards. :P


Top
 Profile  
 
 Post subject:
PostPosted: 14 Sep 2005 10:16 pm 
User avatar

Joined: 26 Feb 2004 03:51 pm
Posts: 3619
Location: Hong Kong
阿邦,我呢隻爛蕉翼有冇得補呀?
Image

原來 SK-II 棒咁有用架!


Top
 Profile  
 
 Post subject:
PostPosted: 18 Sep 2005 07:36 pm 
User avatar

Joined: 03 Mar 2004 07:31 pm
Posts: 1020
:)
Image
Image
Image
Image
Image
:P :P

:P
Image
:P

As I mentioned before, this wing is a shooting star's wing. Changing the tip to a pointed shape, that means the other side have to go through the same processes!! :shock: :shock:


Top
 Profile  
 
 Post subject:
PostPosted: 01 Nov 2005 11:01 am 

Joined: 20 Jul 2004 04:16 pm
Posts: 43
想問噴油方面點樣配油? 點樣可以噴到同本身對翼同色呀? 同埋點樣可以噴到甘光面呀? thx.


Top
 Profile  
 
 Post subject:
PostPosted: 02 Nov 2005 12:53 am 
User avatar

Joined: 03 Mar 2004 07:31 pm
Posts: 1020
:D

Your reply is my compliment! :D

The paint is ordinary canned paint that you could buy in normal hardware shop.

The finishing is a matter of sanding and polishing, plus a little bit of patience.


So work hard!!! :D :D :D

regards,


Top
 Profile  
 
 Post subject:
PostPosted: 02 Nov 2005 09:16 am 

Joined: 20 Jul 2004 04:16 pm
Posts: 43
Pong,
thx for your information. thx.


Top
 Profile  
 
 Post subject:
PostPosted: 19 Dec 2005 10:59 pm 

Joined: 16 Dec 2005 01:20 am
Posts: 93
Dear Pong,

I saw three bottles on display. Other than the Micro ballon, what are the content of the other two ?

Another question, you also displayed a scale, what are the mixture percentage, is it a secret ?

I should be gratful if you would enlighten me.

Philip Shum


Top
 Profile  
 
 Post subject:
PostPosted: 20 Dec 2005 03:52 am 
User avatar

Joined: 03 Mar 2004 07:31 pm
Posts: 1020
:P

I used naminating resin. The mixing ratio is 10:3. (resin to hardener). For such a small section to repair, only a few grams of resin needed. That's why a scale is used.

For your information, naminating resin is different with others, the mixing ratio must be accurate. Otherwise, it will either too soft or too crispy.

Hope you could just enjoy the fun of soaring, but not the cumbersome works for repairing. i.e. No crash, no repairing.

Regards.


Top
 Profile  
 
 Post subject:
PostPosted: 20 Dec 2005 11:21 am 

Joined: 16 Dec 2005 01:20 am
Posts: 93
Dear Pong,

Thank you for your reply.

No, I am not thinking of how to crash while flying. This is only prepare for the worse and if knew what I am capable in the workshop would no doubt give me more confidence whilst my aircraft is airborne.

I think your current thread can form a chapter in a Modle Aircraft Repair Manual.

Very good visual aids has been produced. If a picture is better than a thousand words, then you might have written nearly 20,000 words in the current chapter.

Anyway, I still have a few questions on the current subject.

You have mentioned the mixing ratio about the naminating resin, what about the Micro Ballon? Do you add micro ballon to the mixture ? If so, what is the ratio?

Do you use cloth on the area being repaired? If so, what is it and is there any specifications?

What is the fixing / drying time of the mixed resin ?

Are you using '1500' sand paper? Is this the finest, and do you use coarser sand paper, say '400' / '800' at the beginning of the process?

By the way, is 'SK II' the best? Is there any other recommendations from our lady pilots?

Philip Shum


Top
 Profile  
 
 Post subject:
PostPosted: 21 Dec 2005 12:35 pm 
User avatar

Joined: 03 Mar 2004 07:31 pm
Posts: 1020
:P
- After you had mixed the laminating resin, then stir with micro balloon thoroughly. The ratio need not that accurate. The manual says the ratio is 3 to 1 in volume (3 parts of balloon to one part of mixed resin).
- After the micro balloon is dried, sand it to shape, and then apply a layer of cloth.
- I used glass cloth. 3 ounces per square meter.
- Such laminating epoxy needs 24 hours to dry.
- I think No. 2000 is the finest that you could get from hardware store.
- Yes, I used 800 at first.

- Concerning the stirrer, any SK2, SK3 or even SK9 could do.

Regards.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC + 8 hours


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron

RCSAIL Home

WindGURU at Ma On Shan, Clearwater Bay and Fei Ngo Shan

Powered by phpBB® Forum Software © phpBB Group