| RC Slope Soaring in Hong Kong http://www.rcsail.com/forum/ |
|
| 邊隻叉電器好? http://www.rcsail.com/forum/viewtopic.php?f=3&t=874 |
Page 1 of 1 |
| Author: | Nelson Woo [ Sun Dec 17, 2006 4:12 pm ] |
| Post subject: | 邊隻叉電器好? |
我想買個叉機用黎叉接收既果pack電, 要識叉滿後自動停. 去過鴨寮街睇過又唔知邊隻係, 又唔知點同D店員講, 淨係見到叉普通AA,AAA果D叉電器. 請問大家有冇介紹, 用開邊隻牌子, etc. APEX o岩 唔 o岩用? 另外D 三針插 邊度有得買(平)? 即係SERVO果條紅黑白線連個黑色插呢. 謝謝. |
|
| Author: | Willy Lim [ Mon Dec 18, 2006 11:54 am ] |
| Post subject: | |
我部 Apex Infinity version 1.0, 1998年買，上星期終於發覺壞機（接駁電池後仍話 no battery，不肯充/放電），佢網站話永世保用，我攞返去小西灣廠房，佢話維修要等一個月，但佢無話幾錢，我估真係永世保用。 |
|
| Author: | ken [ Mon Dec 18, 2006 12:37 pm ] |
| Post subject: | |
Nelson, 你搞到今日還未搞掂個充電機.怪不得兩三個星期見不到你在清水灣出現。 話我知你用甚 |
|
| Author: | Nelson Woo [ Mon Dec 18, 2006 2:34 pm ] |
| Post subject: | |
我用緊一隻火牛仔, 可調較輸出voltage: 6V 7.5V 9V. 插住4粒GP牌1.2V(串連後4.8V)(1000mAH)NiMH充電池, 經量度後分別drive到60mA, 110mA, 同170mA. 每次放機前用60mA叉過夜, 三次之後就叉爆左. 另外我買左果隻SUPER牌筆蕊電既叉電器,灰銀色有個液晶顯示果隻,用來叉AA電,佢claim話自己曉停,點知又係叉爆粒AA電, d acid 流左落d線路板上, 連叉機都報燒左. 自從玩rc glider後, 加加埋埋燒左十粒叉電. 依家用緊既係"Ringo牌"叉電4.8V(1800mA)NiMH. 先多謝你, 不過咁, 我都係想正正經經買隻自己曉停既叉機. 想知邊隻牌子係大家都用開有口碑, 唔會連屋都燒埋. |
|
| Author: | Henry Tso [ Mon Dec 18, 2006 9:51 pm ] |
| Post subject: | |
Nelson, 你可以考慮Futaba CR-2000 或 Futaba CR-2500,我現在用緊的 CR-2000 非常靠得住，價錢大約800元已包括火牛。 Henry |
|
| Author: | Henry Tso [ Mon Dec 18, 2006 9:56 pm ] |
| Post subject: | |
Nelson, 差點忘記話你知，呢個係德昌價錢。 |
|
| Author: | kin [ Tue Dec 19, 2006 9:00 pm ] |
| Post subject: | |
K&S PROP II It can charge 1-5 cell lipolyer,1-30 cell ni-cd/nimh,all tybe bettery , DC12v input.... $1300 |
|
| Author: | Nelson Woo [ Wed Dec 20, 2006 4:09 pm ] |
| Post subject: | |
點解d曉停既叉機咁貴? 我以為二三百添. |
|
| Author: | PhilipShum [ Thu Dec 21, 2006 8:35 am ] |
| Post subject: | |
Nelson Woo wrote: 點解d曉停既叉機咁貴? 我以為二三百添.
Dear Nelson, Have you considered the cost of the 'Ten Damaged' rechargable battery, and the 'n' number of battery to follow ? Also, with unreliable charged battery go up with you '$$$$$' glider on the sky ? I think that is why 'intelligent' charger cost you more. Philip Shum |
|
| Author: | wipchu [ Thu Dec 21, 2006 3:28 pm ] |
| Post subject: | |
您可到廣華街睇睇.模型店有串沖叉機賣. 普通300至600元攪掂.最好多D請教老手.知多D. |
|
| Page 1 of 1 | All times are UTC + 8 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|