Hong Kong RC Sailplane Forum 香港滑翔機發燒友論壇
http://www.rcsail.com/forum/

風唔好,為有整
http://www.rcsail.com/forum/viewtopic.php?f=3&t=51
Page 1 of 1

Author:  K.Y.Mak [ 14 Mar 2004 09:10 pm ]
Post subject:  風唔好,為有整

:( 星期六叫亞 CM 去放机,點知引極佢都唔出,話要係屋企整机!我最後都係因為大霧,所以去左大清二樓放机,但係就唔係幾好飛! CM,你好野! :wink:
:oops: 今日 D 風睇泥都唔好得去邊,又好大霧,就去左平洋村找 YC 講既 HLG 大場,但係就點都見唔到個場!唔通真係有 ....... ! 好驚呀 ! :lol:
:( 返到屋企見 D 風都收到勿都冇,就不如學 CM 咁整机好過啦! 結果整左幾個月都未完工兩隻 NewSting 翼尖,卒之噴左油啦。不之幾咁開心 :D

Author:  Y C Lui [ 14 Mar 2004 09:30 pm ]
Post subject: 

先排呢風好好﹐淨係顧著飛﹐也機都唔想整﹐嬾都出汁﹐呢兩日飛得唔過癮﹐先至有番D興致整機﹐依加既目標只係補番隻 mini Corado 黎參加HLG比賽。
Image

Author:  CM Cheng [ 14 Mar 2004 09:44 pm ]
Post subject: 

阿麥,我都好想好想好想去放機架,不過手擲機賽逼近,先至留係屋企整機咋 :D

整左兩日,先造好隻 DLG 個 pod 既 solid model,(係咪好靚仔呢 . . .) 不過以我既速度,九成九整唔起,下星期都係補番隻 Lucia,不過隻 Lucia 撞到內傷,都有排整!

Image

Author:  K.Y.Mak [ 14 Mar 2004 10:22 pm ]
Post subject: 

CM Cheng wrote:
整左兩日,先造好隻 DLG 個 pod 既 solid model,(係咪好靚仔呢 . . .)


CM, 個 pod 真係好靚仔!但係你點出個 mould 呀? 用電腦 CNC 出會唔會好貴呀! :roll:

Author:  CM Cheng [ 15 Mar 2004 01:26 am ]
Post subject: 

我都想 CNC 個模,但係要好多($$$$$$$$$$) :cry:
另一個方法是用 SLA 造個 plug,再做纖維模,不過個 plug 要加工,而且都要($$$$$) :(
亦可以用電腦晝出每一層的 template ,切飛機木片疊起,即好似等高線咁,呢個方法最花工夫,但係最平($) :)

放埋對翼,都差不多勒:

Image

Author:  Y C Lui [ 15 Mar 2004 10:26 am ]
Post subject: 

犀利﹗隻機有名未 ?

Author:  CM Cheng [ 15 Mar 2004 05:58 pm ]
Post subject: 

YC,對個名咁有興趣? 其實如果你 ckeck 下個 filename,大概都會估到她名叫 Apus,出自南天的一個小星座,意為 Bird of Paradise。

Author:  CM Cheng [ 17 Mar 2004 12:33 am ]
Post subject: 

整埋條尾勒:

Image

OK! 可以補Lucia啦!

Author:  Y C Lui [ 17 Mar 2004 12:45 am ]
Post subject: 

CM﹐睇黎隻機都仲要有排至出得世﹐不如將D參數輸入 FMS simulator ﹐睇下佢係電腦入面飛成點。

Author:  Ah Pong [ 17 Mar 2004 11:18 pm ]
Post subject: 

I also repaired my broken NYX, hope she could be tested on forthcoming saturday. :D

Author:  CM Cheng [ 18 Mar 2004 08:05 pm ]
Post subject: 

Y C Lui wrote:
不如將D參數輸入 FMS simulator ﹐睇下佢係電腦入面飛成點。


Hello YC, I've not made a new plane with the FMS before, but I checked the .par file and I think those parameters are mainly used to model an existing airplane. For a plane still on the drawing board (I mean CAD :wink: ) I don't think those parameters can be obtainable without other prediction softwares or wind tunnel tests. Better put the effort on making the plane. It is a lot more fun :!:

Page 1 of 1 All times are UTC + 8 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/