RC Slope Soaring in Hong Kong
http://www.rcsail.com/forum/

風唔好，為有整
http://www.rcsail.com/forum/viewtopic.php?f=3&t=51		 Page 1 of 1
Author:  K.Y.Mak [ Sun Mar 14, 2004 9:10 pm ]
Post subject:  風唔好，為有整
:( 星期六叫亞 CM 去放机，點知引極佢都唔出，話要係屋企整机！我最後都係因為大霧，所以去左大清二樓放机，但係就唔係幾好飛！ CM，你好野！ :wink:
:oops: 今日 D 風睇泥都唔好得去邊，又好大霧，就去左平洋村找 YC 講既 HLG 大場，但係就點都見唔到個場！唔通真係有 ....... ! 好驚呀 ！ :lol:
:( 返到屋企見 D 風都收到勿都冇，就不如學 CM 咁整机好過啦！ 結果整左幾個月都未完工兩隻 NewSting 翼尖，卒之噴左油啦。不之幾咁開心 :D
Author:  Y C Lui [ Sun Mar 14, 2004 9:30 pm ]
Post subject: 
先排呢風好好﹐淨係顧著飛﹐也機都唔想整﹐嬾都出汁﹐呢兩日飛得唔過癮﹐先至有番D興致整機﹐依加既目標只係補番隻 mini Corado 黎參加HLG比賽。
Image
Author:  CM Cheng [ Sun Mar 14, 2004 9:44 pm ]
Post subject: 
阿麥，我都好想好想好想去放機架，不過手擲機賽逼近，先至留係屋企整機咋 :D

整左兩日，先造好隻 DLG 個 pod 既 solid model，(係咪好靚仔呢 . . .) 不過以我既速度，九成九整唔起，下星期都係補番隻 Lucia，不過隻 Lucia 撞到內傷，都有排整!

Image
Author:  K.Y.Mak [ Sun Mar 14, 2004 10:22 pm ]
Post subject: 
CM Cheng wrote:
整左兩日，先造好隻 DLG 個 pod 既 solid model，(係咪好靚仔呢 . . .)


CM, 個 pod 真係好靚仔！但係你點出個 mould 呀？ 用電腦 CNC 出會唔會好貴呀！ :roll:
Author:  CM Cheng [ Mon Mar 15, 2004 1:26 am ]
Post subject: 
我都想 CNC 個模，但係要好多($$$$$$$$$$) :cry:
另一個方法是用 SLA 造個 plug，再做纖維模，不過個 plug 要加工，而且都要($$$$$) :(
亦可以用電腦晝出每一層的 template ，切飛機木片疊起，即好似等高線咁，呢個方法最花工夫，但係最平($) :)

放埋對翼，都差不多勒:

Image
Author:  Y C Lui [ Mon Mar 15, 2004 10:26 am ]
Post subject: 
犀利﹗隻機有名未 ?
Author:  CM Cheng [ Mon Mar 15, 2004 5:58 pm ]
Post subject: 
YC，對個名咁有興趣? 其實如果你 ckeck 下個 filename，大概都會估到她名叫 Apus，出自南天的一個小星座，意為 Bird of Paradise。
Author:  CM Cheng [ Wed Mar 17, 2004 12:33 am ]
Post subject: 
整埋條尾勒:

Image

OK! 可以補Lucia啦!
Author:  Y C Lui [ Wed Mar 17, 2004 12:45 am ]
Post subject: 
CM﹐睇黎隻機都仲要有排至出得世﹐不如將D參數輸入 FMS simulator ﹐睇下佢係電腦入面飛成點。
Author:  Ah Pong [ Wed Mar 17, 2004 11:18 pm ]
Post subject: 
I also repaired my broken NYX, hope she could be tested on forthcoming saturday. :D
Author:  CM Cheng [ Thu Mar 18, 2004 8:05 pm ]
Post subject: 
Y C Lui wrote:
不如將D參數輸入 FMS simulator ﹐睇下佢係電腦入面飛成點。


Hello YC, I've not made a new plane with the FMS before, but I checked the .par file and I think those parameters are mainly used to model an existing airplane. For a plane still on the drawing board (I mean CAD :wink: ) I don't think those parameters can be obtainable without other prediction softwares or wind tunnel tests. Better put the effort on making the plane. It is a lot more fun :!:
Page 1 of 1 All times are UTC + 8 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/