用車床去車鉛ballast有問題,
同一把刀，車銅是OK的＇但銅包鉛就唔得啦！
車速係1200rpm
如下圖:
有冇人知,車鉛應用什麼車刀的呢？
| RC Slope Soaring in Hong Kong http://www.rcsail.com/forum/ |
|
| 車床車鉛應用什麼車刀 http://www.rcsail.com/forum/viewtopic.php?f=3&t=2180 |
Page 1 of 1 |
| Author: | K.Y.Mak [ Thu Feb 09, 2012 11:18 pm ] |
| Post subject: | 車床車鉛應用什麼車刀 |
用車床去車鉛ballast有問題, 同一把刀，車銅是OK的＇但銅包鉛就唔得啦！ 車速係1200rpm 如下圖: 有冇人知,車鉛應用什麼車刀的呢？ |
|
| Author: | CM Cheng [ Fri Feb 10, 2012 12:34 am ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
用打火機"潭"吓就滑滑！！ 
|
|
| Author: | CM Cheng [ Fri Feb 10, 2012 12:37 am ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
快過頭啲鉛熔咗 
|
|
| Author: | Albert [ Fri Feb 10, 2012 1:28 am ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
阿麥今次點解不用什麼『鎢合金』?
|
|
| Author: | K.Y.Mak [ Fri Feb 10, 2012 12:04 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
Albert wrote: 阿麥今次點解不用什麼『鎢合金』? 都玩吓  車銅要用HSS車刀 『鎢合金』用什麼車刀呀 
|
|
| Author: | Kolosun [ Fri Feb 10, 2012 3:03 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
K.Y.Mak wrote: Albert wrote: 阿麥今次點解不用什麼『鎢合金』? 都玩吓 車銅要用HSS車刀 『鎢合金』用什麼車刀呀 Carbide Tools 有 Ti Coating, TiCN Coating,Cubic Boron Nitride ....等等 |
|
| Author: | K.Y.Mak [ Fri Feb 10, 2012 3:55 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
得唔得呀  用鎢合金去車 鎢合金
|
|
| Author: | 小廣 (IQ博士) [ Fri Feb 10, 2012 4:03 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
Kolosun wrote: K.Y.Mak wrote: Albert wrote: 阿麥今次點解不用什麼『鎢合金』? 都玩吓 車銅要用HSS車刀 『鎢合金』用什麼車刀呀 Carbide Tools 有 Ti Coating, TiCN Coating,Cubic Boron Nitride ....等等 我信，因為生哥係專科。 |
|
| Author: | Kolosun [ Fri Feb 10, 2012 4:39 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
有 Ti Coating ,OR 陶瓷刀粒 Attachment: 2012-02-10 14.48.36.jpg [ 232.78 KiB | Viewed 27406 times ] Attachment: 2012-02-10 16.31.40.jpg [ 211.33 KiB | Viewed 27406 times ] Attachment: 2012-02-10 16.35.01.jpg [ 231.47 KiB | Viewed 27406 times ] 但多數人用 WireCut 機做,你係咩用途 ??? |
|
| Author: | K.Y.Mak [ Fri Feb 10, 2012 4:56 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
無呀! 只是吹水 不過弈想過用"合金钨钢圆棒"做ballast http://item.taobao.com/item.htm?id=1316 ... 1hsps28d7a 
|
|
| Author: | Alex SO [ Fri Feb 10, 2012 5:28 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
Ah Mak 車鉛行慢車，5個C咁行，即係每浸都好薄，車出泥的效果就會好靚，巴刀夠利就會好光滑而反光。 千祈唔好大大刀呀！睇你張想認該入刀深左同轉速快左啫。 |
|
| Author: | Kolosun [ Sat Feb 11, 2012 1:15 am ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
MAK 星期日比把車刀你車鉛喇!! |
|
| Author: | Kolosun [ Fri Mar 16, 2012 3:30 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
之前 Attachment: 2012-03-16 09.28.33.jpg [ 278.92 KiB | Viewed 27142 times ] 之後 Attachment: 2012-03-16 13.52.08.jpg [ 346.27 KiB | Viewed 27142 times ] |
|
| Author: | K.Y.Mak [ Fri Mar 16, 2012 3:51 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
依！ 係好o左好多譒！ 請題供技術資料呀. 個邊位重有少少唔光滑、重有冇得整呀？ |
|
| Author: | Kolosun [ Fri Mar 16, 2012 4:27 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
K.Y.Mak wrote: 依！ 係好o左好多譒！ 請題供技術資料呀. 個邊位重有少少唔光滑、重有冇得整呀？ ?????? 重要整,滑個你翼面喎 !!!!!!! 技術資料有MOVIE ,有轉速 460 rpm ,有進刀速度,仲要........??? http://youtu.be/Tb_ZUV29JFw |
|
| Author: | Albert [ Fri Mar 16, 2012 11:26 pm ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
我隻 P3 上次去龍磐 Full-loading 10粒銅... 都食得唔夠飽!! 跑極都唔快!!:? 生哥, 同我車返10粒銅套鉛倉, 唔該!! 
|
|
| Author: | Kolosun [ Sat Mar 17, 2012 1:35 am ] |
| Post subject: | Re: 車床車鉛應用什麼車刀 |
作死你呀 !! 好忙呀 ,你再去龍磐先車 !!! |
|
| Page 1 of 1 | All times are UTC + 8 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|